Search Results

The active components, such as OH and their concentrations in the coflow, have a strong effect on the combustion process of diesel fuel spray flames in the Controllable Active Thermo-Atmosphere (CATA), which then will affect the soot incandescence of the spray flames. CO2 and H2O2, the additives which have contrary effect on the concentration of the active components, were mixed separately into the thermo-atmosphere before the jet spray were issued into the coflow, which changed the boundary condition around the central jet and influenced the combustion characteristics and soot incandescence. The combustion characteristics such as ignition delay and flame liftoff height of the central spray flames are measured and the linkage between these two parameters is investigated at different coflow temperatures.

Idle stopping is one of the most important fuel saving methods for hybrid electric vehicle (HEV). While the enriched injection strategy which was employed to ensure reliable ignition of first cycle will leads to even more fuel film stayed in the intake port, all of the liquid film will evaporate randomly and interfere the mixture air-fuel ratio of the followed cycles. The fuel transport of the first cycle should be enhanced to reduce the residual fuel film, and then the control of the cycle-by-cycle air-fuel ratio will become easier and the combustion and HC emissions will also be better. In this paper the mixture preparation characteristics of the unfired first cycle, as well as the combustion and HC emissions characteristics of the fired first cycle under various injection timing strategies such as close-valve injection, mid-valve injection, and open-valve injection were investigated.

By changing the top-land radial clearance, this paper presents the effect of the piston crevice on the transient HC emissions of the first firing cycle at cold start on an LPG SI Engine. A fast-response flame ionization detector (FFID) was employed to measure transient HC emissions of the first firing cycle. At the same time, the transient cylinder pressure and instantaneous crankshaft speed of the engine were measured and recorded. The results show that increasing 50% crevice volume leads to 25% increase of HC emissions in the lean region and 18% increase of HC emissions in the rich region, however, the 50% increase of crevice volume contributes to 32% decease of HC emissions in the stable combustion region. For LPG SI engine, the HC emissions of the first firing cycle during cold start are relatively low in a wide range of the excess air ratio.

Ion current sensing, which usually employs a spark plug as its sensor to obtain feedback signal from different types of combustion in SI engines, may be applied to HCCI combustion sensing instead of a prohibitively expensive piezoelectric pressure transducer. However, studies showed that the ion current detected by a spark plug sensor is a localized signal within the vicinity of the sensor's electrode gap, being affected by conditions around it. To find out better and feasible ion probe positions, a 3D-CFD model with a detailed surrogate mechanism containing 1423 species and 6106 reactions was employed to study the effect of stratification on ion distribution in HCCI combustion. The simulation results indicate that the monitor probe 1, 8 and 9 are more stable and reliable than the others. IONmax and dIONmax are more accurate to estimate CA50 and dQmax respectively.

The present work discusses a novel oxyfuel combustion method named internal combustion rankine cycle (ICRC) used in reciprocating engines. Water is heated up through heat exchanger by exhaust gas and engine cooling system, and then injected into the cylinder near top dead center to control the combustion temperature and in-cylinder pressure rise rate, meanwhile to enhance the thermo efficiency and work of the combustion cycle. That is because injected water increases the mass of the working fluid inside the cylinder, and can make use of the combustion heat more effectively. Waste heat carried away by engine coolant and exhaust gas can be recovered and utilized in this way. This study investigates the effect of water injection temperature on the combustion and emission characteristics of an ICRC engine based on self-designed test bench. The results indicate that both indicated work and thermal efficiency increase significantly due to water injection process.

This paper presents a study of the influence of intake valve closing (IVC) timing on the performance of the high-speed spark ignition (SI) engine, such as the output of torque and power, fuel consumption and emissions. An electrically controlled Variable Valve Timing (VVT) system based on the variable working position belt extender was developed and its pro-type was successfully set up in a 5-valve, double overhead cam (DOHC) SI engine. Test results showed that the IVC timing plays an important role in increasing the power output, decreasing the fuel consumption and CO and HC emissions under both high- and low-speed conditions as compared to the fixed IVC timing. The control of intake valve closing timing is a simple and effective means to improve engine's performance.

Argon Power Cycle (APC) is an innovative future potential power system for high efficiency and zero emissions, which employs an Ar-O2 mixture rather than air as the working substance. However, APC hydrogen engines face the challenge of knock suppression. Compared to hydrogen, methane has a better anti-knock capacity and thus is an excellent potential fuel for APC engines. In previous studies, the methane is injected into the intake port. Nevertheless, for lean combustion, the stratified in-cylinder mixture formed by methane direct injection has superior combustion performances. Therefore, based on a methane direct injection engine at compression ratio = 9.6 and 1000 r/min, this study experimentally investigates the effects of replacing air by an Ar-O2 mixture (79%Ar+21%O2) on thermal efficiencies, loads, and other combustion characteristics under different excess oxygen ratios. Meanwhile, the influences of varying the methane injection timing are studied.

The conventional transistor coil ignition system with coil-out energy up to 100 mJ might not be sufficient to establish a self-sustained flame kernel under lean combustion with strong in-cylinder flow motion. Further increase of the discharge current will decrease the voltage across the spark gap, which will affect the calculation of the energy delivered to the spark gap. In this paper, the relationship between the discharge current and gap voltage is investigated, and it is discovered that the spark energy doesn,t increase monotonously with the increase of the discharge current. However, engine test results still indicate a positive impact of discharge current amplitude on the engine performance.

Advances in engine technology in recent years have led to significant reductions in the emission of pollutants and gains in efficiency. As a facet of investigations into clean, efficient combustion, the homogenous charge compression ignition (HCCI) mode of combustion can improve upon the thermal efficiency and nitrogen oxides emission of conventional spark ignition engines. With respect to conventional diesel engines, the low nitrogen oxides and particulate matter emissions reduce the requirements on the aftertreatment system to meet emission regulations. In this paper, n-butanol, an alcohol fuel with the potential to be derived from renewable sources, was used in a light-duty diesel research engine in the HCCI mode of combustion. Control of the combustion was implemented using the intake pressure and external exhaust gas recirculation. The moderate reactivity of butanol required the assistance of increased intake pressure for ignition at the lower engine load range.

Modern diesel engines were known for producing ultra-low levels of hydrogen and hydrocarbons. However, as emission control techniques such as exhaust gas recirculation (EGR) are implemented to meet stringent NOx standards, the resulting increase in partial-combustion products can be significant in quantity both as pollutants and sources of lost engine efficiency. In this work, a modern common-rail diesel engine was configured to investigate the EGR threshold for elevated carbon monoxide, hydrocarbon, and hydrogen emissions at fixed loads and fixed heat-release phasing. It is noted that increase in hydrocarbons, in particular light hydrocarbons (such as methane, ethylene, and acetylene) was concurrent with ultra-low NOx emissions. Hydrogen gas can be emitted in significant quantities with the application of very high EGR. Under ultra-low NOx production conditions for medium and high load conditions, the light hydrocarbon species can account for the majority of hydrocarbon emissions.

For internal combustion engine systems, lean and diluted combustion is an important technology applied for fuel efficiency improvement. Because of the thermodynamic boundary conditions and the presence of in-cylinder flow, the development of a well-sustained flame kernel for lean combustion is a challenging task. Reliable spark discharge with the addition of enhanced delivered energy is thus needed at certain time durations to achieve successful combustion initiation of the lean air-fuel mixture. For a conventional transistor coil ignition system, only limited amount of energy is stored in the ignition coil. Therefore, both the energy of the spark discharge and the duration of the spark discharge are bounded. To break through the energy limit of the conventional transistor coil ignition system, in this work, an adaptive spark ignition system is introduced. The system has the ability to reconstruct the conductive ion channels whenever it is interrupted during the spark discharge.

Diesel aided by gasoline low temperature combustion offers low NOx and low soot emissions, and further provides the potential to expand engine load range and improve engine efficiency. The diesel-gasoline operation however yields high unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions. This study aims to correlate the chemical origins of the key hydrocarbon species detected in the engine exhaust under diesel-gasoline operation. It further aims to help develop strategies to lower the hydrocarbon emissions while retaining the low NOx, low soot, and efficiency benefits. A single-cylinder research engine was used to conduct the engine experiments at a constant engine load of 10 bar nIMEP with a fixed engine speed of 1600 rpm. Engine exhaust was sampled with a FTIR analyzer for speciation investigation.

In this paper, the spray and combustion characteristics of biodiesel and diesel were investigated. The spray pictures of single injection, by means of a diesel pump test-bed, were taken by a high-speed camera video system in an atmospheric condition, and the effects of the pump speed, nozzle orifice diameter and nozzle opening pressure on the fuel spray structure and characteristics were studied under atmosphere condition. The results showed that the general law of biodiesel spray characteristics was similar to that of diesel. However, the spray penetration of biodiesel was longer than that of diesel, and the spray angles of biodiesel were only half angle of diesel. The experiment of combustion characteristics was conducted in a vitiated coflow combustor with the same diesel pump test-bed. The images of combustion flame were recorded by the high-speed camera system. Then the ignition characteristics were evaluated from the digital pictures by computer.

Engine-off strategy are popular used in hybrid electric vehicles (HEV) for fuel saving. The engine of an HEV will start and stop frequently according to the road condition. In order to obtain excellent fuel economy and emissions performance, the fuel injection during engine quick start should be optimized. In this paper, the characteristic of mixture formation and the HC emissions at the first 5 cycles which contribute the most HCs were investigated. After the analysis of mixture preparation during start process, the HC emissions during engine quick start were optimized by means of cycle-by-cycle fuel injection control strategy. The fuel mixture concentration during start-up process fluctuates more dramatically under hot start condition. Typically, the mixture at 4th and 5th cycle is over-riched. Based on the original engine calibration, the fuel injection at the initial 5 cycles was optimized respectively.

A segment of steel tube with the inner diameter of 60 mm and length of 100 mm was fixed between the intake manifold and cylinder head in a direct injection natural aspirated diesel engine. The surface of the tube could be heated to be above 400 °C by the heater enwrapped outside within several minutes under the power less than 600 W. The tip of an injector traditionally used for in-cylinder diesel direct injection was extended to the axis of the tube. The diesel sprays could impinge onto the hot inner surface of the tube and atomize quickly if the temperature of the tube was high enough. Then the fuel-air mixture would be sucked into the cylinder, and HCCI combustion could be fulfilled. The vaporization ratio of the impinged diesel sprays was estimated by fuel consumption, intake air flux and excess air coefficient (λ) calculated from the volumetric concentration of O2, CO2 and CO emissions. The NOx emission was always very low.

The use of gasoline fuels in compression ignition engines, with or without diesel pilots, has shown encouraging progress in engine efficiency and emissions. The dual fuel combustion of gasoline-diesel offers the flexibility of modulating the cylinder charge reactivity, but an accurate and reliable control over the ignition in the dual fuel applications is more challenging than in classical engines. In this work, the gasoline-diesel dual fuel operation is investigated on a single cylinder research engine. The effects of the intake boost, exhaust gas recirculation (EGR) rates, diesel/gasoline ratio, and diesel injection timing are studied in regard to the ignition control. The results indicate that at low load, a diesel pilot can improve the cylinder charge reactivity and reduce emissions of incomplete combustion products.

In order to improve the fuel economy for future high-efficiency spark ignition engines, the use of advanced combustion strategies with an overall lean and/or exhaust gas recirculation diluted cylinder charge is deemed to be beneficial, provided a reliable ignition process available. In this paper, experimental results of igniting methane-air mixture by means of capacitive coupled ignition and multi-coil distributed spark ignition are presented. It is found that with a conventional spark plug electrode configuration, increase of spark energy does not proportionally enhance the ignition flame kernel development. The use of capacitive coupled ignition to enhance the initial transient power resulted in faster kernel growth compared to the conventional system. The distribution of the spark energy across a number of spark gaps shows considerable benefit.

In this paper, a low-speed pre-ignition (LSPI) diagnostic strategy is designed based on the ion current signal. Novel diagnostic and re-injection strategies are proposed to suppress super-knock induced by pre-ignition within the detected combustion cycle. A parallel controller system that integrates a regular engine control unit (ECU) and CompactRIO (cRIO) from National Instruments (NI) is employed. Based on this system, the diagnostic and suppression strategy can be implemented without any adaptions to the regular ECU. Experiments are conducted on a 1.5-liter four-cylinder, turbocharged, direct-injected gasoline engine. The experimental results show two kinds of pre-ignition, one occurs spontaneously, and the other is induced by carbon deposits. Carbon deposits on the spark plug can strongly interfere with the ion current signal. By applying the ion current signal, approximately 14.3% of spontaneous and 90% of carbon induced pre-ignition cycles can be detected.

This paper presents an investigation of cold starts based on a cycle-by-cycle control strategy in an LPG EFI engine. Experiments were carried out in a four-stroke, water-cooled, single cylinder, 125cc SI engine with an EFI system. Effects of the first injection pulse width and the first combustion cycle on the characteristics of the cold-start were analyzed based on the histories of transient engine speeds and cylinder pressures. The study focuses on how to realize the controllable ignition cycle and the single-cycle and multi-cycle combustions were tested based on the single starting injection pulse width. Test results show that the first combustion cycle has an important effect on HC emission and combustion stability of following cycles at cold-start. The injection pulse width is the key factor determining the characteristics of an ignition cycle during the cold-start.

A cycle-resolved test system was designed in a Two Stage Direct Injection (TSDI) Gasoline engine to simulate the engine quick start process in an Integrated Start and Generator (ISG) Hybrid Electric Vehicle (HEV) system. Based on the test system, measurement of the in cylinder HC concentrations near the spark plug under different engine coolant temperature and cranking speed conditions were conducted using a Fast Response Flame Ionization Detector (FFID) with Sampling Spark Plug (SSP) fits, then the in-cylinder equivalence ratio near the spark plug was estimated from the measured HC concentrations. In addition, the effects of the 1st injection timing, 2nd injection timing, and total equivalence ratio on the mixture formation near the spark plug were analyzed by means of experiments.